(Eng/Esp) 👽 My little keychain martian 👽 Mi pequeño marcianito llavero 👽
Hello my dear readers, I hope you are well and that you have or have had an excellent day. I have had a few scraps of fabric for some time, and I really had no idea what to do with them because they are so small, until I decided to use them: But what could I do with some scraps of green fabric, what could I make that would look good in that color, and I remembered the aliens, and I decided to make one that would look quite cute and tender at the same time. So today I want to share with you how I made a little martian that I will use as a keychain.
STEP BY STEP:
To make this Martian the first thing I am going to make is a pattern, so I will take the sheet and pencil and draw the Martian, as shown in the image. As many know aliens are quite abnormal, so I drew the head big and the body quite small.
With the green fabric scraps cut two pieces of the Martian, place the pattern you made on top of the fabric and cut all around the edge.
Now that I have my two pieces cut out, I proceed to glue with the silicone on all the edges, leaving an opening without glue, so I can fill the body with the cotton.
I will now continue cutting out the eyes, with the black fabric, I will cut out two large ovals and with the white fabric, I will cut out four small drop-shaped pieces, which are the ones that make the eyes sparkle.
After I have the eye pieces cut out, with the silicone I will glue the white pieces on the black ovals and these in turn, I will glue them on the Martian's face.
With the white fabric I will cut a flannel for the Martian, so I will place the Martian on top of the white fabric and cut out just the desired size. Then with the silicon I will glue it to the body of the Martian.
Once the flannel is attached to the body, I stuff the whole Martian with the cotton and with the silicone I carefully close the opening where I stuffed it.
Cut a strip of 1 cm wide by 3 cm long approximately, to make the handle where it will hang and with the silicon I will glue it to the back of the Martian's head, as shown in the image.
And now I have the little martian ready to take it anywhere, I love the way it looks, I hope you do too.
I say goodbye as always, but not before thanking you for dedicating a little of your valuable time to visit my blog, I hope to see you in my next publication. Be well, take care of yourselves, see you soon.
Original creation content:
✴️ All photos are my own taken and edited with my Alcatel cell phone.
✴️ The cover image was made with the Canva application and edited by me.
✴️ The divider was taken from Canva and edited by me in Paint.
✴️ The English translation was done with the help of DeepL.
✴️ The language indication letters, were taken from the Cooltext page and edited by me.
Hola mis queridos lectores, espero que se encuentren bien y que tengan o hayan tenido un excelente día. Tengo desde hace tiempo unos cuantos retacitos de tela, que realmente no tenía ni idea de qué hacer con ellos por los pequeños que son, hasta que me decidí usarlos: ¿Pero qué podría hacer con unos retazos de tela verde, que podría hacer que se viera bien en ese color?, y me acordé de los extraterrestres, y me decidí hacer uno que se viera bastante coqueto y tierno a la vez. Así que el día de hoy quiero compartir con ustedes como realice un marcianito que lo usaré como llavero.
PASO A PASO:
Para realizar este marciano lo primero que voy a hacer es un patrón, así que tomaré la hoja y el lápiz y dibujaré el marciano, tal como se muestra en la imagen. Como muchos saben los extraterrestres son bastante anormales, así que le dibuje la cabeza grande y el cuerpo bastante pequeño.
Con los retazos de tela verde corte dos piezas del marciano, coloque el patrón que realice encima de la tela y corte por todo el borde.
Ahora que tengo mis dos piezas recortadas, procedo a pegar con el silicón, por todos los bordes, dejando una abertura sin pegar, para poder rellenar el cuerpo con el algodón.
Continuaré ahora recortando los ojos, con la tela negra, recortaré dos óvalos grandes y con la tela blanca, recortaré cuatro piezas pequeñas tipo gota, que son los que hacen que le den el brillo a los ojos.
Luego que tengo las piezas de los ojos recortados, con el silicón pegaré las piezas de color blanco en los óvalos negros y estos a su vez, los pegaré en la cara del marciano.
Con la tela blanca cortaré una franela para el marciano, así que colocaré el marciano encima de la tela blanca y recortaré justo el tamaño deseado. Luego con el silicon lo pegaré al cuerpo del marciano.
Ya con la franela pegada al cuerpo, relleno todo el marciano con el algodón y con el silicon con mucho cuidado, cierro la abertura por donde rellene.
Corte una tira de 1 cm de ancho por 3 de largo aproximadamente, para hacer el asa por donde se colgara y con el silicon lo pegaré a la parte de atrás de la cabeza del marciano, tal como se muestra en la imagen.
Y ya tengo el marcianito listo para llevarlo a cualquier lado, a mí me encanto como quedo, espero que a ustedes también.
Me despido como siempre, no sin antes agradecerles por dedicarme un poquito de su valioso tiempo para visitar mi blog, los espero en mi próxima publicación. Pórtense bien, cuídense mucho, hasta pronto.
Contenido de la creación original:
✴️ Todas las fotos son propias tomadas y editadas con mi móvil Alcatel.
✴️ La imagen de portada fue hecha con la aplicación Canva y editada por mí.
✴️ El separador fue tomado de Canva y editado por mí en Paint.
✴️ La traducción al inglés se hizo con la ayuda de DeepL.
✴️ Las letras de indicación del idioma, fueron tomadas de la página Cooltext y editadas por mí.