It's a hectic photo, but I picked up a @mapexdrums Falcon snare stand today. I've been needing another stand for a while and @rezdrums had one in stock. I traded a couple snares in and got some heads/sticks

IT RUNS!!! Thanks to @bcekli for stopping by and spraying starter fluid. Don't mind the extra noises. I forgot to quit cranking the starter. #mustang #fordmustang #starterfluid #silverbullitt

I got the aftermarket JVC head unit out, along with the abandoned factory CD player. It was oddly difficult to pull out. I think the extra wires were crammed in there and preventing enough slack. I have

Live electrical outlets should probably be shut off at the breaker before I yank the rest of this off of the wall. I had to get inventive with the temporary caps on the sink drain. Back to the store for

I'm not sure if it's just a pony with mange, or if it's a baby snake shedding its skin because it wants to be a Cobra when it grows up. #paint #bodywork #mange #snakeskin #mustang #fordmustang #silverbullitt

It has the mange. #silverbullitt #projectsilverbullitt #mustang #fordmustang #paint #bodywork #avgfloridian #averagefloridian #avgfl

Decided to go to @spanxthehogbbq for dinner and there was a car show going on. #bbq #carshow #mustang #jaguar #thunderbird #f150 #firetruck #tbird #etype #fairladyz #cadillac #cadillaccts

It's done! Well, I have to caulk, but that's boring. The magic combination was a 90° street elbow to connect the P-trap, then a couple reducer bushings for the 3/4" to connect on the other side. I

You might remember the temporary studio lighting solution. You might also remember the permanent solution installed as a test setting. Well, now it's all legit and on the circuit with the switches. No

We're out here checking out #dipcon2018 with @dipyourcar @dipexclusive @drpigment @famouscustomz @kppigments @vossen @dippworxx @goldcoastdips @404kustomsatl @miamidips @rde_customs @thespraysource

The scooter project is in a lull. Waiting for tools and making decisions on parts. The owner said her shop replaced the original 50cc engine with a 100cc engine. I took measurements and it looks like she

We're at the Pompano Beach Cultural Center for a presentation on "Pompano Complete Streets." You can go to commission meetings and project proposals wherever you live. We suggest getting involved

Having multiple ongoing projects can also be a curse. These brick pavers had a purpose. They were never installed. An unfortunate event rendered their existence meaningless. I am helping move them for

The only redeeming part of having more projects than you can possibly work on is that when other projects hit a lull, there's always something else you can work on. Tonight was a convenient time to strip

The sink was bent and I had some high spots in the finish. After some hammering, sanding and Demelling, it's all flat enough to caulk in. This was boring and self explanatory, so I didn't film. Next step

Well, I took too long applying some of the finish and it began to harden, so I will have to do some sanding. It took 2 quarts to finish this counter top. It's rough, kind of like the rest of the table.

I mentioned I had a water supply leak in the house. It's patched up now with a #sharkbite coupling. It's not ideal, but this will all be fully repiped when I renovate the kitchen and bathroom. It looks

If you are reading this, please bring beer. It's been a while, but I finally found the leak in the house... kinda sorta. I'm digging out this defunct water softener tonight so we have room to work and

Well, a good portion of Famwood's Glaze Coat soaked into the plywood. I mixed up what I had left to fill in some of the low spots. I will have to buy another quart of this stuff and do it all again tomorrow.

It doesn't come out well in the picture, but there is epoxy on the top. Coverage was thin in some areas. We'll see how it levels out and go over any low spots with whatever is left. I used Glaze Coat by