[ESP- ING] ENSEÑANDO COMO HACER UNA ZAPATERA / TEACHING HOW TO MAKE A COBBLER

SEGUNDO PASO.

Luego corte cada una de las piezas que lleva.

1. Parte número 1.
   Una pieza en Semicuero mostaza de 46cm por 100cm luego se dobla y se le quitan 8 cm en las esquinas de abajo y en el centro queda igual

2. Parte número 2.
   Una pieza en plástico transparente de 46cm por 100cm, luego se dobla y se les cortan en la parte de arriba 8cm en el centro y queda igual en las esquinas.
   En la parte de abajo se les cortan los 8cm en las esquinas y en el centro queda igual

1. Parte número 3.
   Dos piezas en Semicuero de 46cm por 94 cm

2. Parte número 4.
   Una pieza en Semicuero de 46cm por 94 cm

3. Parte número 5.
   Una pieza en Semicuero de 46cm por 94 cm

4. Parte número 6.
   Una pieza en Semicuero de 16cm por 48cm

5. Parte número 7. O separadores
   Doce piezas en Semicuero de 16cm por 26cm luego se dobla y quita en las esquina de abajo un cuadrito de un centímetro, es lo que permite crear la pestaña para la unión en el centro con la parte cinco (5)

6. Parte número 8.
   Tres piezas en Semicuero de 4cm por 12cm. Esta es para crear las agarraderas o las hazas

STEP TWO.

Then cut out each of the pieces you are carrying.

1. Part number 1.
   A piece in mustard semi leather of 46cm by 100cm then fold it and take off 8 cm at the bottom corners and in the center it remains the same.

1. Part number 2.
   A piece of transparent plastic 46cm by 100cm, then folded and cut 8cm in the center at the top and the corners remain the same.
   In the bottom part cut 8cm in the corners and in the center remains the same.

1. Part number 3.
   Two semi-leather pieces of 46cm by 94cm.

1. Part number 4.
   One piece of half leather 46 cm by 94 cm.

1. Part number 5.
   One piece in half leather 46 cm by 94 cm.

1. Part number 6.
   One piece in half leather of 16cm by 48cm.

1. Part number 7. Or separators
   Twelve pieces in half leather of 16cm by 26cm then fold and remove in the bottom corner a square of one centimeter, is what allows to create the tab for the union in the center with part five (5).

1. Part number 8.
   Three pieces in Semicuero of 4cm by 12cm. This is to create the grips or the handles.

TERCER PASO

STEP THREE

After cutting all the pieces.
The next step is to sew the hem on all sides to part number one (1).

Also place part number two (2), which is the plastic, the edges or part number three (3) and the reinforcement or part number four (4) which is in the center.

Sew the hem on the sides to part number five (5).
Sew the hem on the sides facing outward to part number six (6).
Sew the hem on the side facing out to the twelve (12) pieces of part number (7), these are the dividers.
And double stitch the three pieces of part number eight (8) which are to make the three rows.

CUARTO PASO
Una vez terminados todos los ruedos se marca con tiza o color en la parte número (1) donde van cada uno de los separadores
Asimismo en la parte numero dos (2) y en la parte número cinco (5) se marca también donde van cada uno de los separadores.

STEP FOUR

Once all the rows are finished, mark with chalk or color on the part number (1) where each of the separators go.
Also in part number two (2) and part number five (5) also mark where each one of the separators go.

FIFTH STEP

Then proceed to sewing:
Between the part number one (1) and part (2) goes the part number six (6) if you prefer it should be fixed with pins or with a stitch with needle and thread before, so as not to make a mistake.

SIXTH STEP

Then glue the part number (5) and each of the spacers, which are twelve in total, in each of the marked points, fixing them also with pins or stitches so as not to make a mistake

Bueno hasta la próxima y muchas bendiciones

FINAL PRODUCT

And this is how the finished work turned out.
Well I really enjoyed with my friend this project, to show her how to make a cobbler, especially because my friend is a beautiful person.
Well until next time and many blessings