Samsung Galaxy A03 with a Charging Issue. Diagnosis and Repair / Samsung Galaxy A03 con falla de carga. Diagnóstico y reparación.
[ENG]
Good afternoon, @Geek Zone community and the rest of Hive.
We continue with the repairs in our workshop. We carry out several repairs every day. Today, we present the case of a Samsung A03 that won't charge. The customer tells us that they have to move the USB cable from side to side to get it to charge, and even then, it takes a very long time to finish.
As usual, we will proceed with the diagnosis and, afterward, the repair, provided it is within our capabilities.
DIAGNOSIS
1- Without disassembling the device, we visually inspect the charging port. It looks quite worn. However, we need to be sure, and measurements are what provide that certainty.
2- We will take an initial measurement using our power supply as a tester. We set it to 5 V and connect the USB cable to the phone. We observe that there is no current consumption. Here, we verify that the device is indeed not charging.
3- Now we will open the device. Since the port pins are located on the underside, we are going to measure at the Sub Board FPC. To find out which one is the charging line here, we will look it up using our Circuit Bit tool.
Once opened, we can see that this line is at the far left of the FPC. We take a measurement and obtain 0.4 mV.
4- Since no voltage reaches the Sub Board FPC connector, we already know that the problem is either in the charging port or in one of the components along the line running from the port to the FPC. We remove the phone's Sub Board, turn it over, connect the USB cable, and measure the voltage at the positive and negative pins, which are located at the ends. We obtain -225.8 mV, so we have now identified the problem. Without a doubt, the charging port is damaged.
REPAIR
1- Since we already know that the damage is in the charging port, we will proceed to replace it. We will mount our Sub Board on a lifting fixture with alligator clips.
2- We will set our hot air station to 480 degrees and apply heat to the port until we remove it. This process takes barely 40 seconds. We wait about 4 minutes for the board to cool down.
3- Next, we will remove the residual solder remaining in the 4 holes where the port's anchor points are located. For this, we will use desoldering braid and the soldering iron until they are completely clean.
4- We install the new port and solder the 4 anchor points. We solder the 5 rear pins. We repeat the measurement, this time at the FPC, and that's it! We now have 5 V.
5- We install the Sub Board back into the phone. We repeat the process of connecting the USB cable using the power supply as a tester, and we now have confirmation that the phone is charging. There is current consumption of 0.486 A. We can also see the charging notification in the phone's battery icon in the upper-right corner. Everything is ready to be handed back to the customer.
That concludes this repair process. Fortunately, the problem was the charging port. Sometimes, any of the overvoltage or overcurrent protection components in the charging line may be damaged, or the charging IC itself may be faulty. In those cases, the repair is a little more complex, especially when it comes to finding the replacement part.
In cases like this, where the port is damaged, we always recommend that the customer also have their charging cable checked, since it can sometimes be damaged as well. Because there is a connection between the USB cable and the port, the possibility of one damaging the other does exist.
Thank you to all our readers for your attention. All images are my own work.
Translated with the help of Google Translate.
See you soon.
[ESP]
Buenas tardes, comunidad @Geek Zone y el resto de Hive.
Continuamos con las reparaciones en el taller. Son varias las que hacemos en el día. Hoy les presentamos el caso de un Samsung A03 que no carga. El cliente nos comenta que tiene que mover el cable USB de un lado a otro para que cargue y, aun así, se demora cantidad para terminar.
Procederemos como es habitual, haremos el diagnóstico y, posterior a ello, la reparación, siempre y cuando esté a nuestro alcance.
DIAGNÓSTICO
1- Sin desarmar el equipo, hacemos inspección visual al puerto de carga; en este, se ve bastante desgastado. No obstante, debemos estar seguros, y la seguridad la dan las mediciones.
2- Haremos una primera medición, usaremos nuestra fuente como tester, la regulamos a 5 V, conectamos el cable USB al móvil. Observamos que no hay consumo. Aquí verificamos que ciertamente el equipo no carga.
3- Ahora abriremos el equipo. Como los pines del puerto están de la parte de abajo, vamos a medir en el FPC de la Sub Board. Para saber cuál es la línea de carga aquí, buscaremos en nuestra herramienta Circuit Bit.
Al abrirlo, aquí vemos que esta línea es en el extremo izquierdo del FPC. Medimos y obtenemos 0.4 mV.
4- Como al conector del FPC de la Sub Board no llega el voltaje, ya sabemos que el problema está o en el puerto de carga o en algún elemento de los que están en la línea que va desde el puerto al FPC. Retiramos la Sub Board del teléfono, la volteamos, conectamos el cable USB y medimos voltaje en los pines positivo y negativo, que son los extremos. Obtenemos -225.8 mV, así que aquí ya está el problema. Sin duda, es el puerto de carga que está dañado.
REPARACIÓN
1- Como ya sabemos que el daño está en el puerto de carga, procederemos a cambiarlo. Montaremos nuestra Sub Board en un elevador con caimanes.
2- Graduaremos nuestra estación de calor en 480 grados y daremos calor sobre el puerto hasta retirarlo. Este proceso apenas dura unos 40 segundos. Esperamos unos 4 minutos para que enfríe la placa.
3- Seguido, retiraremos el estaño residual que se queda en los 4 agujeros donde van los anclajes del puerto. Para esto usaremos la malla desoldadora y el cautín hasta que queden totalmente limpios.
4- Montamos el nuevo puerto, soldamos los 4 anclajes. Soldamos los 5 pines posteriores. Repetimos la medición ahora en el FPC y listo, ya tenemos los 5 V.
5- Montamos la Sub Board al teléfono. Repetimos el proceso de conectar el cable USB usando la fuente como tester y ya tenemos la reafirmación de que el teléfono está cargando, ya existe consumo de corriente, 0.486 A, vemos además en la esquina superior derecha la notificación en la batería del móvil que ya está cargando. Todo listo para entregar al cliente.
Hasta aquí este proceso de reparación. Afortunadamente, es el pin de carga, en ocasiones puede estar dañada cualquiera de las protecciones contra sobre tensión o sobre corriente que hay en la línea de carga, o el IC de carga y entonces es un poco mas complejo sobre todo a la hora de conseguir el respuesto. En estos casos, donde es puerto esta dañado, siempre recomendamos al cliente además hacer una revisión de su cable de carga, pues en ocasiones también se encuentra dañado, y como existe una sincronizacion entre el cable USB y el puerto, el que uno dañe al otro es una posibilidad que existe.
Gracias a los lectores por su atención. Todas las imágenes son de mi total autoría.
Traducido con ayuda del traductor de Google.
Hasta pronto.