Saludos Hive.
Continuando con el proyecto de las 9 máquinas para riego. Ya habíamos visto la caja de succión y el cómo se instalaba el equipo de bombeo con todos sus accesorios.
Ahora veremos los detalles de ejecución de la conductora que va desde la estación de bombeo hasta la máquina. Es evidente, son 9 equipos de bombeo, por ende, son 9 conductoras. Expondremos una para ejemplificar, el resto es el mismo proceso.
Como plano ejecutivo para que el constructor se guíe para construir, presentaremos el perfil longitudinal. El perfil, como en la imagen, es un corte del terreno visto de forma transversal relacionando distancias y cotas a partir de un origen que es la caseta de bombeo.
Como especificaciones mostradas en el perfil resaltamos que:
La tubería irá soterrada a una profundidad de forma tal que el recubrimiento mínimo sobre la misma será de 0.7 m.
El ancho de la zanja será el diámetro de la tubería más 20 centímetros a cada lado.
La tubería irá apoyada sobre un prepiso de arena con 10 centímetros de espesor.
Se rehinchará 30 centímetros sobre la corona del tubo con un rehincho fino, y posteriormente con el propio material de la excavación.
En el caso expuesto, existe una válvula de ventosa; se colocan en cambios de pendientes, puntos altos, cambios de diámetros. Su función es la de expulsar el aire de la tubería y evitar que este aire obstruya el paso del agua. De igual forma, en caso de vaciado de la tubería, absorbe aire para evitar presión negativa y con ello que la tubería se aplaste.
En algunos casos que el perfil lo requiera, se colocan válvulas de desagüe. Se ubican en puntos bajos, su función es desaguar la tubería para casos de limpieza.
En cada plano se expone además una tabla con los volúmenes de tierra a excavar, el volumen del prepiso de arena, rehincho fino, rehincho grueso y el material que se excava y sobra, y por ende hay que transportar.
En la parte inferior del perfil, en forma de tabla, también están los valores de distancia, cota, pendiente de la tubería, profundidad de excavación, cotas de fondo de la tubería.
Hasta pronto. Que tengan buenas tardes.
Greetings Hive.
Continuing with the project of the 9 irrigation machines. We had already seen the suction box and how the pumping equipment was installed with all its accessories.
Now we will look at the execution details of the pipeline that goes from the pumping station to the machine. Obviously, there are 9 pumping systems, therefore, there are 9 pipelines. We will present one as an example; the rest follow the same process.
As an executive plan to guide the builder, we will present the longitudinal profile. The profile, as shown in the image, is a cross-section of the terrain, correlating distances and elevations from an origin point, which is the pumping station house.
As for the specifications shown in the profile, we highlight that:
The pipeline will be buried at a depth such that the minimum cover over it will be 0.7 m.
The width of the trench will be the diameter of the pipe plus 20 centimeters on each side.
The pipe will rest on a 10-centimeter-thick sand bedding.
It will be backfilled with fine material up to 30 centimeters above the top of the pipe, and subsequently with the excavated material itself.
In the case presented, there is an air release valve (ventosa); these are placed at slope changes, high points, and diameter changes. Its function is to expel air from the pipeline and prevent this air from obstructing the water flow. Similarly, in case the pipeline is drained, it admits air to prevent negative pressure and thus avoid the collapse of the pipe.
In some cases where the profile requires it, drain valves are placed. They are located at low points, and their function is to drain the pipeline for cleaning purposes.
Each plan also displays a table with the volumes of earth to be excavated, the volume of the sand bedding, fine backfill, coarse backfill, and the excavated material that is left over and therefore must be hauled away.
At the bottom of the profile, also in table format, are the values for distance, elevation, pipeline slope, excavation depth, and pipe invert levels (bottom elevations of the pipe).
See you soon. Have a good afternoon.