Source: https://en.wikipedia.org/wiki/American_wire_gauge
American Wire Gauge (AWG) is a logarithmic stepped standardized wire gauge system used since 1857, predominantly in North America, for the diameters of round, solid, nonferrous, electrically conducting wire. Dimensions of the wires are given in ASTM standard B 258.[1] The cross-sectional area of each gauge is an important factor for determining its current-carrying capacity.
The AWG originated in the number of drawing operations used to produce a given gauge of wire. Very fine wire (for example, 30 gauge) required more passes through the drawing dies than 0 gauge wire did. Manufacturers of wire formerly had proprietary wire gauge systems; the development of standardized wire gauges rationalized selection of wire for a particular purpose.
While the AWG is essentially identical to the Brown & Sharpe (B&S) sheet metal gauge, the B&S gauge was designed for use with sheet metals. These are functionally interchangeable, but the use of B&S in relation to wire gauges, rather than sheet metal gauges, is technically improper.
Increasing gauge numbers denote logarithmically decreasing wire diameters, which is similar to many other non-metric gauging systems such as British Standard Wire Gauge (SWG). However, AWG is dissimilar to IEC 60228, the metric wire-size standard used in most parts of the world, based directly on the wire cross-section area (in square millimetres, mm2).
The AWG tables are for a single, solid and round conductor. The AWG of a stranded wire is determined by the cross-sectional area of the equivalent solid conductor. Because there are also small gaps between the strands, a stranded wire will always have a slightly larger overall diameter than a solid wire with the same AWG.
By definition, 36 AWG is 0.005 inches in diameter, and 0000 AWG is 0.46 inches (11.68 mm) in diameter. The ratio of these diameters is 1:92, and there are 40 gauge sizes from 36 to 0000, or 39 steps. Because each successive gauge number increases cross sectional area by a constant multiple, diameters vary geometrically. Any two successive gauges (e.g., A and B) have diameters whose ratio (dia. B ÷ dia. A) is (approximately 1.1229), while for gauges two steps apart (e.g., A, B, and C), the ratio of C to A is about 1.12292 ≈ 1.2610. Similarly for gauges n steps apart, the diameter ratio of the first to last gauges is about 1.1229n.
The diameter of an AWG wire is determined according to the following formula:
Where n is the AWG size for gauges from 36 to 0. For larger gauges n = −1 for 00, n = −2 for 000, and n = −3 for 0000.
or equivalently:
The gauge can be calculated from the diameter using [2]
and the cross-section area is
.
The standard ASTM B258-02 (2008), Standard Specification for Standard Nominal Diameters and Cross-Sectional Areas of AWG Sizes of Solid Round Wires Used as Electrical Conductors, defines the ratio between successive sizes to be the 39th root of 92, or approximately 1.1229.[3] ASTM B258-02 also dictates that wire diameters should be tabulated with no more than 4 significant figures, with a resolution of no more than 0.0001 inches (0.1 mils) for wires thicker than 44 AWG, and 0.00001 inches (0.01 mils) for wires 45 AWG and thinner.
Sizes with multiple zeros are successively thicker than 0 AWG and can be denoted using "number of zeros/0", for example 4/0 AWG for 0000 AWG. For an m/0 AWG wire, use n = −(m − 1) = 1 − m in the above formulas. For instance, for 0000 AWG or 4/0 AWG, use n = −3.
The sixth power of is very close to 2,[4] which leads to the following rules of thumb:
When the cross-sectional area of a wire is doubled, the AWG will decrease by 3; for example, two 14 AWG wires have about the same cross-sectional area as a single 11 AWG wire. This doubles the electrical conductance.
When the diameter of a solid round wire is doubled, the AWG will decrease by 6; for example, 1 mm diameter wire is ≈18 AWG, 2 mm diameter wire is ≈12 AWG, and 4 mm diameter wire is ≈6 AWG. This quadruples the cross-sectional area and conductance.
A decrease of ten gauge numbers; for example, from 24 AWG to 14 AWG multiplies the area, weight, and conductance by approximately 10.
Convenient coincidences result in the following rules of thumb for resistances:
The resistance of copper wire is approximately 1 Ω/1000 ft for 10 AWG, 10 Ω/1000 ft for 20 AWG, 100 Ω/1000 ft for 30 AWG, and so on.[5]: 27 For an arbitrary gauge n, it is approximately 10n/10 Ω per 10000 ft.
Because aluminum wire has a conductivity of approximately 61% of copper, an aluminum wire has nearly the same resistance as a copper wire that is two sizes smaller, which has 62.9% of the area.
Tables of AWG wire sizes[edit]
The table below shows various data including both the resistance of the various wire gauges and the allowable current (ampacity) based on a copper conductor with plastic insulation. The diameter information in the table applies to solid wires. Stranded wires are calculated by calculating the equivalent cross sectional copper wire area. Fusing current (melting wire) is estimated based on 25 °C (77 °F) ambient temperature. The table below assumes DC, or AC frequencies equal to or less than 60 Hz, and does not take skin effect into account. "Turns of wire per unit length" refers to wire wound in a helix with the turns touching, as in a solenoid and is therefore the reciprocal of the conductor diameter. As wire in such a coil normally has insulation, this figure forms an upper bound.[6]
↑ For enclosed wire at 30 °C ambient,[8] with given insulation material temperature rating, or for single unbundled wires in equipment for 16 AWG and thinner.[9]
↑ or, equivalently, Ω/km
↑ or, equivalently, Ω/kft
Jump up to: 1 2 3 4 Exactly, by definition
In the North American electrical industry, conductors thicker than 4/0 AWG are generally identified by the area in thousands of circular mils (kcmil), where 1 kcmil = 0.5067 mm2. The next wire size thicker than 4/0 has a cross section of 250 kcmil. A circular mil is the area of a wire one mil in diameter. One million circular mils is the area of a circle with 1,000 mil (1 inch) diameter. An older abbreviation for one thousand circular mils is MCM.
Stranded wire AWG sizes[edit]
AWG can also be used to describe stranded wire. The AWG size of a stranded wire represents the sum of the cross-sectional diameter of the individual strands; the gaps between strands are not counted. When made with circular strands, these gaps occupy about 25% of the wire area, thus requiring the overall bundle diameter to be about 13% larger than a solid wire of equal gauge.
Stranded wires are specified with three numbers, the overall AWG size, the number of strands, and the AWG size of a strand. The number of strands and the AWG size of a strand are separated by a slash. For example, a 22 AWG 7/30 stranded wire is a 22 AWG wire made from seven strands of 30 AWG wire.
As indicated in the Formulae and Rules of thumb sections above, differences in AWG size translate directly into ratios of diameter or area. This property can be employed to easily find the AWG size of a stranded bundle by measuring the diameter and count of its strands. (This only applies to bundles with circular strands of identical size.) To find the AWG size of 7-strand wire with equal strands, subtract 8.4 from the AWG size of a strand. Similarly, for 19-strand subtract 12.7, and for 37 subtract 15.6.
Measuring strand diameter is often easier and more accurate than attempting to measure bundle diameter and packing ratio. Such measurement can be done with a wire gauge go-no-go tool or with a caliper or micrometer.
Nomenclature and abbreviations in electrical distribution[edit]
Alternative ways are commonly used in the electrical industry to specify wire sizes as AWG.
4 AWG (proper)
#4 (the number sign is used as an abbreviation of "number")
№ 4 (the numero sign is used as an abbreviation for "number")
No. 4 (an approximation of the numero is used as an abbreviation for "number")
No. 4 AWG
4 ga. (abbreviation for "gauge")
000 AWG (proper for thick sizes)
3/0 (common for thick sizes) Pronounced "three-aught" or "triple-aught"
3/0 AWG
#000
AWG is colloquially referred to as gauge and the zeros in thick wire sizes are referred to as aught . Wire sized 1 AWG is referred to as "one gauge" or "No. 1" wire; similarly, thinner sizes are pronounced "x gauge" or "No. x" wire, where x is the positive-integer AWG number. Consecutive AWG wire sizes thicker than No. 1 wire are designated by the number of zeros:
No. 0, often written 1/0 and referred to as "one-aught" or "single-aught" wire
No. 00, often written 2/0 and referred to as "two-aught" or "double-aught" wire
No. 000, often written 3/0 and referred to as "three-aught" or "triple-aught" wire
and so on.
IEC 60228, international standards for wire sizes
French gauge
Brown & Sharpe
Circular mil, North American Electrical industry standard for wires thicker than 4/0.
Standard wire gauge or SWG, has a similar but not interchangeable numbering scheme to AWG.
Birmingham Wire Gauge
Stubs Iron Wire Gauge
Jewelry wire
Body jewelry sizes, which commonly uses AWG especially for thinner sizes, even when the material is not metallic.[17]
Electrical conductor
Electrical wiring
Number 8 wire, a term used in the New Zealand vernacular
↑ "ASTM B258-14 Standard Specification for Standard Nominal Diameters and Cross-sectional Areas of AWG Sizes of Solid Round Wires Used as Electrical Conductors". West Conshohocken, Pennsylvania: ASTM International. Archived from the original on 22 July 2014. Retrieved 22 March 2015.
↑ The logarithm to the base 92 can be computed using any other logarithm, such as common or natural logarithm, using log92x = (log x)/(log 92).
↑ ASTM Standard B258-02, page 4
↑ The result is approximately 2.0050, or 1/2 of one percent greater than 2.
↑ Copper Wire Tables (Technical report). Circular of the Bureau of Standards No. 31 (3rd ed.). United States Department of Commerce. October 1, 1914.
↑ Adam, Lekchu. "chart".
↑ Figure for solid copper wire at 68 °F (20 °C), (Not in accordance to NEC Codebook 2014 Ch. 9, Table 8) computed based on 100% IACS conductivity of 58.0 MS/m, which agrees with multiple sources:
Lund, Mark. "American Wire Gauge table and AWG Electrical Current Load Limits". Powerstream.com. Retrieved 2008-05-02. (although the ft/m conversion seems slightly erroneous)
Belden Master Catalog, 2006, although data from there for gauges 35 and 37–40 seem obviously wrong.
High-purity oxygen-free copper can achieve up to 101.5% IACS conductivity; e.g., the Kanthal conductive alloys data sheet lists slightly lower resistances than this table.
↑
NFPA 70 National Electrical Code 2014 Edition Archived 2008-10-15 at the Wayback Machine. Table 310.15(B)(16) (formerly Table 310.16) page 70-161, "Allowable ampacities of insulated conductors rated 0 through 2000 volts, 60°C through 90°C, not more than three current-carrying conductors in raceway, cable, or earth (directly buried) based on ambient temperature of 30°C." Extracts from NFPA 70 do not represent the full position of NFPA and the original complete Code must be consulted. In particular, the maximum permissible overcurrent protection devices may set a lower limit.
↑ "Table 11: Recommended Current Ratings (Continuous Duty) for electronic equipment and chassis wiring". Reference Data for Engineers: Radio, Electronics, Computer and Communications (7th ed.). pp. 49–16.
↑
Computed using equations from Beaty, H. Wayne; Fink, Donald G., eds. (2007), The Standard Handbook for Electrical Engineers (15th ed.), McGraw Hill, pp. 4–25, ISBN 978-0-07-144146-9
↑ Brooks, Douglas G. (December 1998), "Fusing Current: When Traces Melt Without a Trace" (PDF), Printed Circuit Design, 15 (12): 53, archived from the original (PDF) on 2016-03-27, retrieved 2016-08-01
↑
Preece, W. H. (1883), "On the Heating Effects of Electric Currents", Proceedings of the Royal Society, 36 (36): 464–471, Bibcode:1883RSPS...36..464P
↑
Preece, W. H. (1887), "On the Heating Effects of Electric Currents", Proceedings of the Royal Society, II (43): 280–295
↑
Preece, W. H. (1888), "On the Heating Effects of Electric Currents", Proceedings of the Royal Society, III (44): 109–111
Jump up to: 1 2
Brooks, Douglas G.; Adam, Johannes (29 June 2015), "Who Were Preece and Onderdonk?", Printed Circuit Design and Fab
↑
Stauffacher, E. R. (June 1928), "Short-time Current Carrying Capacity of Copper Wire" (PDF), General Electric Review, 31 (6)
↑ "Body Jewelry Size Reference". SteelNavel.com. Archived from the original on 19 January 2022. — illustrating the different ways that size is measured on different kinds of jewelry
Interactive Wire Size and Voltage Drop Calculator (AWG/mm²) — Tool for calculating required wire gauge and voltage drop based on circuit length, current, and temperature compensation.
ASTM B258 Standard Specification for AWG Sizes
Archived URL: https://en.wikipedia.org/wiki/American_wire_gauge
�� CONTENT HASHES:
SHA-256: 81c2112973f04b30b3d00a23b5f1bcdb994ccf59191a78f1c5b4b8a3542b8db7
BLAKE2b: f975d7006da9864859d34a9307222075c9ab52ae79cce0b3596cdbb3cb6367b6
MD5: ca24aa3972e74588c043ab959c0fbf42
�� TITLE HASHES:
SHA-256: 9dfe14a4e7ccc5cbe18c648dece9ffc32f53fb89c277ddf99a26ba1b98acc54f
BLAKE2b: afe57a5ffeb3009f12c8131c61368e88d1b567b0561dfd2df269f780239ca29d
MD5: b2123c1932dc9f7fb42747a3ec341233
�� INTEGRITY HASHES:
SHA-256: 8bde1eed376699906db5d99193e9945503858c7fb878c421f90c554eb70a8548
BLAKE2b: 49789baa81c37db0cbd6233feec7ac743d488a697511d22781baf97202c3dd32
MD5: d99edbb995e926afe60d3a7d7e197a5d
Archived with ArcHive - Client-side cryptographic archival system