Source: https://en.wikipedia.org/wiki/Electric_potential
Not to be confused with Voltage.
Electric potentialElectric potential around two oppositely charged conducting spheres. Purple represents the highest potential, yellow zero, and cyan the lowest potential. The electric field lines are shown leaving perpendicularly to the surface of each sphere.Common symbolsV, φSI unitvoltOther unitsstatvoltIn SI base unitsV = kg⋅m2⋅s−3⋅A−1Extensive?yesDimensionM L2 T−3 I−1
Electric potential, also known as the electric field potential, potential drop, the electrostatic potential, is the difference in electric potential energy per unit of electric charge between two points in a static electric field. More precisely, electric potential is the amount of work needed to move a test charge from a reference point to a specific point in a static electric field, normalized to a unit of charge. The test charge used is small enough that disturbance to the field-producing charges is unnoticeable, and its motion across the field is supposed to proceed with negligible acceleration, so as to avoid the test charge acquiring kinetic energy or producing radiation. By definition, the electric potential at the reference point is zero units. Typically, the reference point is earth or a point at infinity, although any point can be used.
In classical electrostatics, the electrostatic field is a vector quantity expressed as the gradient of the electrostatic potential, which is a scalar quantity denoted by V or occasionally φ,[1] equal to the electric potential energy of any charged particle at any location (measured in joules) divided by the charge of that particle (measured in coulombs). By dividing out the charge on the particle a quotient is obtained that is a property of the electric field itself. In short, an electric potential is the electric potential energy per unit charge.
This value can be calculated in either a static (time-invariant) or a dynamic (time-varying) electric field at a specific time with the unit joules per coulomb (J⋅C−1) or volt (V). The electric potential at infinity is assumed to be zero.
In electrodynamics, when time-varying fields are present, the electric field cannot be expressed only as a scalar potential. Instead, the electric field can be expressed as both the scalar electric potential and the magnetic vector potential.[2] The electric potential and the magnetic vector potential together form a four-vector, so that the two kinds of potential are mixed under Lorentz transformations.
Practically, the electric potential is a continuous function in all space, because a spatial derivative of a discontinuous electric potential yields an electric field of impossibly infinite magnitude. Notably, the electric potential due to an idealized point charge (proportional to 1 ⁄ r, with r the distance from the point charge) is continuous in all space except at the location of the point charge. Though electric field is not continuous across an idealized surface charge, it is not infinite at any point. Therefore, the electric potential is continuous across an idealized surface charge. Additionally, an idealized line of charge has electric potential (proportional to ln(r), with r the radial distance from the line of charge) is continuous everywhere except on the line of charge.
Classical mechanics explores concepts such as force, energy, and potential.[3] Force and potential energy are directly related. A net force acting on any object will cause it to accelerate. As an object moves in the direction of a force acting on it, its potential energy decreases. For example, the gravitational potential energy of a cannonball at the top of a hill is greater than at the base of the hill. As it rolls downhill, its potential energy decreases and is being translated to motion – kinetic energy.
It is possible to define the potential of certain force fields so that the potential energy of an object in that field depends only on the position of the object with respect to the field. Two such force fields are a gravitational field and an electric field (in the absence of time-varying magnetic fields). Such fields affect objects because of the intrinsic properties (e.g., mass or charge) and positions of the objects.
An object may possess a property known as electric charge. Since an electric field exerts force on a charged object, if the object has a positive charge, the force will be in the direction of the electric field vector at the location of the charge; if the charge is negative, the force will be in the opposite direction.
The magnitude of force is given by the quantity of the charge multiplied by the magnitude of the electric field vector,
Electric potential around separate positive and negative point charges shown as color range from magenta (+), through yellow (0), to cyan (−). Circular contours are equipotential lines. Electric field lines leave the positive charge and enter the negative charge.Electric potential in the vicinity of two opposite point charges.
An electric potential at a point r in a static electric field E is given by the line integral
where C is an arbitrary path from some fixed reference point to r; it is uniquely determined up to a constant that is added or subtracted from the integral. In electrostatics, the Maxwell-Faraday equation reveals that the curl is zero, making the electric field conservative. Thus, the line integral above does not depend on the specific path C chosen but only on its endpoints, making well-defined everywhere. The gradient theorem then allows us to write:
This states that the electric field points "downhill" towards lower voltages. By Gauss's law, the potential can also be found to satisfy Poisson's equation:
where ρ is the total charge density and denotes the divergence.
The concept of electric potential is closely linked with potential energy. A test charge, q, has an electric potential energy, UE, given by
The potential energy and hence, also the electric potential, is only defined up to an additive constant: one must arbitrarily choose a position where the potential energy and the electric potential are zero.
These equations cannot be used if , i.e., in the case of a non-conservative electric field (caused by a changing magnetic field; see Maxwell's equations). The generalization of electric potential to this case is described in the section § Generalization to electrodynamics.
Electric potential due to a point charge[edit]
The electric potential created by a charge, Q, is V = Q/(4πε0r). Different values of Q yield different values of electric potential, V, (shown in the image).
The electric potential arising from a point charge, Q, at a distance, r, from the location of Q is observed to be
where ε0 is the permittivity of vacuum[4], VE is known as the Coulomb potential. Note that, in contrast to the magnitude of an electric field due to a point charge, the electric potential scales respective to the reciprocal of the radius, rather than the radius squared.
The electric potential at any location, r, in a system of point charges is equal to the sum of the individual electric potentials due to every point charge in the system. This fact simplifies calculations significantly, because addition of potential (scalar) fields is much easier than addition of the electric (vector) fields. Specifically, the potential of a set of discrete point charges qi at points ri becomes
where
r is a point at which the potential is evaluated;
ri is a point at which there is a nonzero charge; and
qi is the charge at the point ri.
And the potential of a continuous charge distribution ρ(r) becomes
where
r is a point at which the potential is evaluated;
R is a region containing all the points at which the charge density is nonzero;
r' is a point inside R; and
ρ(r') is the charge density at the point r'.
The equations given above for the electric potential (and all the equations used here) are in the forms required by SI units. In some other (less common) systems of units, such as CGS-Gaussian, many of these equations would be altered.
Generalization to electrodynamics[edit]
When time-varying magnetic fields are present (which is true whenever there are time-varying electric fields and vice versa), it is not possible to describe the electric field simply as a scalar potential V because the electric field is no longer conservative: is path-dependent because (due to the Maxwell-Faraday equation).
Instead, one can still define a scalar potential by also including the magnetic vector potential A. In particular, A is defined to satisfy:
where B is the magnetic field. By the fundamental theorem of vector calculus, such an A can always be found, since the divergence of the magnetic field is always zero due to the absence of magnetic monopoles. Now, the quantity
is a conservative field, since the curl of is canceled by the curl of according to the Maxwell–Faraday equation. One can therefore write
where V is the scalar potential defined by the conservative field F.
The electrostatic potential is simply the special case of this definition where A is time-invariant. On the other hand, for time-varying fields,
unlike electrostatics.
The electrostatic potential could have any constant added to it without affecting the electric field. In electrodynamics, the electric potential has infinitely many degrees of freedom. For any (possibly time-varying or space-varying) scalar field, 𝜓, we can perform the following gauge transformation to find a new set of potentials that produce exactly the same electric and magnetic fields:[5]
Given different choices of gauge, the electric potential could have quite different properties. In the Coulomb gauge, the electric potential is given by Poisson's equation
just like in electrostatics. However, in the Lorenz gauge, the electric potential is a retarded potential that propagates at the speed of light and is the solution to an inhomogeneous wave equation:
The SI derived unit of electric potential is the volt (in honor of Alessandro Volta), denoted as V, which is why the electric potential difference between two points in space is known as a voltage. Older units are rarely used today. Variants of the centimetre–gram–second system of units included a number of different units for electric potential, including the abvolt and the statvolt.
Galvani potential versus electrochemical potential[edit]
Inside metals (and other solids and liquids), the energy of an electron is affected not only by the electric potential, but also by the specific atomic environment that it is in. When a voltmeter is connected between two different types of metal, it measures the potential difference corrected for the different atomic environments.[6] The quantity measured by a voltmeter is called electrochemical potential or fermi level, while the pure unadjusted electric potential, V, is sometimes called the Galvani potential, ϕ. The terms "voltage" and "electric potential" are a bit ambiguous but one may refer to either of these in different contexts.
Charge configuration
Figure
Electric potential
Infinite wire
where is uniform linear charge density.
Infinitely large surface
where is uniform surface charge density.
Infinitely long cylindrical volume
where is uniform linear charge density.
Spherical volume
outside the sphere, where is the total charge uniformly distributed in the volume.
inside the sphere, where is the total charge uniformly distributed in the volume.
Spherical surface
outside the sphere, where is the total charge uniformly distributed on the surface.
inside the sphere for uniform charge distribution.
Charged Ring
on the axis, where is the total charge uniformly distributed on the ring.
Charged Disc
on the axis, where is the uniform surface charge density.
Electric Dipole
on the equatorial plane.
on the axis (given that ), where can also be negative to indicate position at the opposite direction on the axis, and is the magnitude of electric dipole moment.
Absolute electrode potential
Electrochemical potential
Electrode potential
^ Goldstein, Herbert (June 1959). Classical Mechanics. United States: Addison-Wesley. p. 383. ISBN 0201025108.
^ Griffiths, David J. (1999). Introduction to Electrodynamics. Pearson Prentice Hall. pp. 416–417. ISBN 978-81-203-1601-0.
^ Young, Hugh A.; Freedman, Roger D. (2012). Sears and Zemansky's University Physics with Modern Physics (13th ed.). Boston: Addison-Wesley. p. 754.
^ "2022 CODATA Value: vacuum electric permittivity". The NIST Reference on Constants, Units, and Uncertainty. NIST. May 2024. Retrieved 2024-05-18.
^ Griffiths, David J. (1999). Introduction to Electrodynamics (3rd ed.). Prentice Hall. p. 420. ISBN 013805326X.
^ Bagotskii VS (2006). Fundamentals of electrochemistry. John Wiley & Sons. p. 22. ISBN 978-0-471-70058-6.
Politzer P, Truhlar DG (1981). Chemical Applications of Atomic and Molecular Electrostatic Potentials: Reactivity, Structure, Scattering, and Energetics of Organic, Inorganic, and Biological Systems. Boston, MA: Springer US. ISBN 978-1-4757-9634-6.
Sen K, Murray JS (1996). Molecular Electrostatic Potentials: Concepts and Applications. Amsterdam: Elsevier. ISBN 978-0-444-82353-3.
Griffiths DJ (1999). Introduction to Electrodynamics (3rd. ed.). Prentice Hall. ISBN 0-13-805326-X.
Jackson JD (1999). Classical Electrodynamics (3rd. ed.). USA: John Wiley & Sons, Inc. ISBN 978-0-471-30932-1.
Wangsness RK (1986). Electromagnetic Fields (2nd., Revised, illustrated ed.). Wiley. ISBN 978-0-471-81186-2.
Archived URL: https://en.wikipedia.org/wiki/Electric_potential
�� CONTENT HASHES:
SHA-256: 6a0aed35a859b6c4b5f699705dd8819aab3aada208d3fbfbceb11c7966ae618b
BLAKE2b: 82580af307d5a1dd5dd656b1a97edff9b5fbeaa9fa4f9163f1ab6e26c02a23f8
MD5: a5c9ef97d28c1173782ef6b98f69211b
�� TITLE HASHES:
SHA-256: 81a1eafcde3bf9521b4da460863fb87ad69b7ce40ffda4e44e787672240fedfd
BLAKE2b: fa1b863c27ac96b647c826d4d1e5bd88c1f0b0bfa73e661e319a64151cb9359c
MD5: 3adf5f097d12ccfa030135ee7e7544b5
�� INTEGRITY HASHES:
SHA-256: 995c9abb5decbe2a19db451d6c34aac7b3d3f1cefd12a49ad0c6b545f0ddba93
BLAKE2b: e7daa29b5c00956f5aa281bc02d1a18443c8e1007e4a5734c14fbe7e02e7a8db
MD5: c9f2f7861ba07c7998951940e1bce4b7
Archived with ArcHive - Client-side cryptographic archival system