Tutorial how to fix the charging pin of a rechargeable led lamp. For geek zone. [Eng/Esp] [Eng/Esp
Ingles
| Hello friends of the beautiful geek zone community, how are you? |
|---|
For those of you who live in the country of Venezuela the power is going out very often, and it seems that this will be for 3 months.
We are used to buying these rechargeable light bulbs when the power goes out and they are very useful. However, unfortunately they come with a flaw from the factory and that is that their charging pin is very delicate.
To my workshop arrive numbers of these bulbs to just place the charging pin, since a small child, or perhaps a carelessness, or blow, or dropped it, makes the charging pin of this lamp simply receive the damage. So here is the video.
Here you can learn that with just an inexpensive soldering iron and a Phillips screwdriver, you can get the job done. Here is the video.
Talking about the content, this not only works for us, but also for people who don't have a heating station. They can take this video as a reference, since I only used a soldering iron, it is very simple.
This video can also serve as a reference for people who have damaged the charging pin of any other rechargeable lamp OR anything else that has this charging pin, because the procedure is simple, you just have to have good eyesight, good pulse and patience. You can do it.
| Enough with the introduction, let's go to the video! |
|---|
Tools:
- A soldering iron.
- A number 5 slotted screwdriver.
- A small fine tweezers for mobile equipment.
- Tin
- Multimeter
Procedure:
- Using the screwdriver remove the side screws holding the lamp cover.
- Then lift off the lamp cover.
- Then you must loosen the screw that holds the base plate to the board (being very careful not to pull the wires and break them).
- After locating the charging pin you must test that it is good to mount it. If it is not, you must buy another one.
How to verify that it is good?
|------------|
Place the multimeter on voltage scale and place the leads of the multimeter on each pole of the charging pin, and that the multimeter is connected to the charger. If it sends enough 4.7 volts, then it is good.
- Then we must clean the charging pin of tin residue with the same soldering iron.
- Then you must clean the base of the board where the charging pin is soldered with the same soldering iron.
- You must also clean the pins of the negative and positive poles of the charging pin.
-Then you must bend the pins outwards so that when it sticks with the board then they are well pressed. - After this with the tweezers we must hold the charging pin to the board.
- With the soldering iron and tin we must solder each side of the charging pin to the base which is the board.
- Then we must solder the poles of the charging pin to the board.
| There we will have our charging pin soldered. The only thing left to do is to assemble and test. |
|---|
Caution:
- When uncovering the lamp cover. Be careful with the wires that hold to not break them.
- When soldering the pin we must do it carefully so as not to touch any component of the board and damage it.
- When cleaning the charging pin and the base of the board we must be careful not to get too hot and not to bend the poles of the charging pin.
- When you are soldering this part, put more tin on it than this to make it harder than before.
Thanks so much for reading my friends 馃挭馃徎
| content sources |
|---|
- Text translation: www.deepl.com
- Photo and video: Picsart pro. YouCut. Samsung Galaxy j6 plus.
- Source of authorship: own original
- Gift creation: www.canva.com
- Music of the video Copyright free: Here
Espa帽ol
| Hola amigos de la hermosa comunidad de geek zone. 驴C贸mo est谩n? |
|---|
Para los que viven en el pa铆s de Venezuela 煤ltima mente se est谩 yendo la luz muy seguido, y parece que esto ser谩 por 3 meses.
Acostumbramos a cuando se va la luz comenzar a comprar estos bombillos recargables que son muy 煤tiles. Sin embargo, lamentablemente vienen con una falla de f谩brica y es que su pin de carga es muy delicado.
A mi taller llegan n煤meros de estos bombillos para solo colocarle el pin de carga, ya que un ni帽o peque帽o, o tal vez un descuido, o golpe, o lo dejaron caer, hace que el pin de carga de esta l谩mpara simplemente reciba el da帽o. Por eso aqu铆 est谩 el video.
Aqu铆 puedes aprender que con 煤nicamente un caut铆n econ贸mico y un destornillador de estr铆a, puedes hacer el trabajo. Por ac谩 les dejo este video.
Ablando del contenido esto no nada m谩s funciona para nosotros, sino que tambi茅n sirve para las personas que no tienen estaci贸n de calor. Ellas pueden tomar este video de referencia, ya que 煤nicamente use un caut铆n, es muy sencillo.
Este video tambi茅n puede servir de referencia para las personas que tiene da帽o el pin de carga de cualquier otra l谩mpara recargable O cualquier otra cosa que tenga este pin de carga, porque el procedimiento es simple, solamente debes tener buena vista, buen pulso y paciencia. Que t煤 lo puedes hacer.
| 隆隆Ya vasta de introducci贸n, vamos con el video!! |
|---|
Herramientas:
- Un caut铆n.
- Un destornillador de estr铆a n煤mero 5.
- Una pinza fina peque帽a para equipos m贸viles.
- Esta帽o
- Mult铆metro
Procedimiento:
- Con el destornillador sacar los tornillos laterales que sujetan la tapa de la l谩mpara.
- Luego levantar la tapa de la l谩mpara.
- Despu茅s debes soltar el tornillo que sujeta la placa base a la placa (con mucho cuidado de no jalar los cables y romperlos).
- Luego de localizar el pin de carga debes probar que est茅 bueno para montarlo. Si no lo est谩 debes comprar otro.
| 驴Como verificar que est茅 bueno? |
|---|
Colocar el mult铆metro en escala de voltaje y colocar los cables de 茅l en cada polo del pin de carga, y que el este conectado al cargador. Si te manda lo suficiente 4.7 volts, entonces est谩 bueno.
- Luego debemos limpiar el pin de carga de los residuos de esta帽o con el mismo caut铆n.
- Despu茅s debes limpiar la base de la placa donde va soldando el pin de carga con el mismo caut铆n.
- Tambi茅n debes limpiar los pines de los polos negativo y positivo del pin de carga.
-Luego debes doblar los pines hacia fuera para que cuando pegue con la placa entonces est茅n bien presionados. - Despu茅s de esto con la pinza debemos sujetar el pin de carga a la placa.
- Con el caut铆n y esta帽o debemos soldar cada lado del pin de carga a la base que es la placa.
- Despu茅s debemos soldar los polos del pin de carga a la placa.
| All铆 ya tendremos nuestro pin de carga soldado. Solo queda armar y probar. |
|---|
Precauciones:
- Al destapar la tapa de la l谩mpara. Tener cuidado con los cables que sujetan para no romperlos.
- Al soldar el pin debemos hacerlo con cuidado para no tocar ning煤n componente de la placa y da帽arlo.
- Al limpiar el pin de carga y la base de la placa debemos tener cuidado de no calentar mucho y no doblar los polos del pin de carga.
- Cuando est茅s soldado esta pieza, col贸cale m谩s esta帽o que el que tiene esto para que quede m谩s duro que antes.
Muchas gracias por leer mis amigos 馃挭馃徎
| fuentes del contenido |
|---|
- Traducci贸n del texto: www.deepl.com
- Foto y video: Picsart pro. YouCut. Samsung Galaxy j6 plus.
- Fuente de Autor铆a: original propio
- Creaci贸n de gift: www.canva.com
- Musica del video Sin derecho de autor: Aqui
鈻讹笍 3Speak