In this tutorial you will learn:
Know the LIFA_Base interface to communicate Arduino with LabVIEW.
Program the Arduino Uno card from LabVIEW.
Identify the arduino functions encoded in the LIFA_Base.
Domain of Arduino programming
Knowledge of LabVIEW Programming
Port handling of the Arduino Uno card.
Know the IDE of Arduino.
The tutorial presents a contribution to programming the Arduino Uno using the Arduino IDE, from the LabVIEW graphical programming software with the LIFA_Base interface to make the conversion between both programming codes.
Arduino: It is an open source electronic platform, based on software (C / C ++ language) and hardware. Arduino represents a software design company with hardware, the latter consisting of electronic cards, based on microcontrollers and with an open source development environment (IDE) for the programming of each board.
Features of the Arduino Uno: Atmega 328, 14 digital inputs / outputs (6 can be used as PWM), 6 analog inputs and a 16MHz crystal, USB cable. 5V operation voltage. Voltage range from 7 to 12V. Flash Memory: 32KB. EEPROM: 1KB.
We will program the following application: Use the reading port of the Arduino Uno, to read the impedance variation of a potentiometer and use this variation of impedance to show the input voltage in an indicator in LabVIEW, programmed in a visual interface in LabVIEW. We will use the LIFA-Base to communicate the Arduino with LabVIEW, the figure shown below exposes the LabVIEW interface that will be controlled by Arduino through LIFA_Base.
The steps described below, exposes the process to perform Arduino communication with LabVIEW using LIFA_Base.
Program the Arduino in the IDE. The Arduino presents an IDE as a programming interface, which can be downloaded from the official Arduino website https://www.arduino.cc/. The programming interface establishes a series of configuration and connection options, a programming zone where the code and the compilation zone are established.
Download the free software VI Package Manager (VIPM), where you can download the toolkit of the functions or subprograms of Arduino with LabVIEW and the LIFA_Base file, as shown in the following figure:
You can download the free version of the following link: http://www.jki.net/vipm/download The program allows you to download the LabVIEW interface for Arduino program, this program will be the one that downloads and installs the functions of Arduino in LabVIEW.
Once the system has recognized Arduino, the programming is done with the sketch that communicates the board with LabVIEW, this sketch is installed with the file LIFA_Base, in the route shown below:
In the LIFA_Base directory there is the file LIFA_Base.pde, where all the libraries will open to program the Arduino Uno card. This way the Arduino board will be able to communicate with LabVIEW. As shown in the following figure:
Configure the Arduino Uno card in the Arduino programming IDE, for this we select: Tools> Arduino Uno board. As shown in the following figure:
Proceed to look in the IDE tools menu, the communication port where the card is connected, the Arduino Uno card presents a USB communication port. In the image you can see the port selection:
Review in LabVIEW the functions downloaded by the LabVIEW interface for Arduino program. All the functions of Arduino, generate a direct connection of LabVIEW with the input and output ports of the Arduino Uno card, the following figure shows the function of Arduino in LabVIEW, some examples and applications:
The LabVIEW program code is established, in the programming diagram in Graphical language, using the programming functions for reading the analog ports of the Arduino Uno card. In the following image the Arduino program is observed, with the functions of starting the connection with the Arduino, reading the port in a repetitive cycle, closing the communication and detecting errors of the functions in the communication.
The user interface is observed on the front panel of LabVIEW, in this interface you can see a virtual voltmeter used to measure the analog voltage of the Arduino Uno card port, a numerical selector for the analog reading port and a stop button to close the cyclic sequence of the program.
In the LIFA_Base, the LabVIEW interface is generated in Arduino programming code, in order to execute the data reading function of the analog port in the LabVIEW-Arduino connection.
The Low Level Analog Commands code is used to read from the analog port of the Arduino Uno card, then the code in Arduino that generates the LIFA_Base for this function is shown and it depends on the port and configuration that is made in LabVIEW:
Low Level - Analog Commands
*************************************************************************/
case 0x08: // Read Analog Pin
retVal = analogRead(command[2]);
Serial.write( (retVal >> 8));
Serial.write( (retVal & 0xFF));
break;
case 0x09: // Analog Read Port
analogReadPort();
break;
The functions generated by the LIFA_Base to read the analog ports and send the data frames using the serial port are the following:
*************************************************************************/
// Reads all 6 analog input ports, builds 8 byte packet, send via RS232.
void analogReadPort()
{
// Read Each Analog Pin
int pin0 = analogRead(0);
int pin1 = analogRead(1);
int pin2 = analogRead(2);
int pin3 = analogRead(3);
int pin4 = analogRead(4);
int pin5 = analogRead(5);
//Build 8-Byte Packet From 60 Bits of Data Read
char output0 = (pin0 & 0xFF);
char output1 = ( ((pin1 << 2) & 0xFC) | ( (pin0 >> 8) & 0x03) );
char output2 = ( ((pin2 << 4) & 0xF0) | ( (pin1 >> 6) & 0x0F) );
char output3 = ( ((pin3 << 6) & 0xC0) | ( (pin2 >> 4) & 0x3F) );
char output4 = ( (pin3 >> 2) & 0xFF);
char output5 = (pin4 & 0xFF);
char output6 = ( ((pin5 << 2) & 0xFC) | ( (pin4 >> 8) & 0x03) );
char output7 = ( (pin5 >> 6) & 0x0F );
// Write Bytes To Serial Port
Serial.print(output0);
Serial.print(output1);
Serial.print(output2);
Serial.print(output3);
Serial.print(output4);
Serial.print(output5);
Serial.print(output6);
Serial.print(output7);
To finish, we made the connection of the Arduino Uno card through the USB port with the computer that has the LIFA_Base application and the program in LabVIEW, we proceed to test the analogical acquisition of the voltage coming from the potentiometer, as shown in the figure, different voltage values are observed for variations of the potentiometer. The analog port used for the Arduino card is A0.
Thank you very much for your attention…