Hey people, I’ve been dealing with(still dealing) a lot in real life the past two days and haven’t really been very active for personal reasons beyond my control. I’m here today with a rather interesting story though, if you like.
So today I opened my first laptop. Major achievement lol. I did it in an attempt to help my friend 
This story is reversed because I forgot to show you guys what I was doing when I started, only remembered to take pictures to show you when I was closing it back up. So instead of showing you things from the beginning, I’m showing you things from the end to genesis lol. You’ll understand though. If you start reading this post from the bottom up, that basically gives you the start to finish arrangement.
So this is what the inside looked like when I opened. Confusing, I know! As someone doing this for the first time, the only thing I knew was where to locate the hard disk and the cmos battery. I suspected the problem was related to the hard disk since it said no boot device found. I checked the hard disk cable connections and there was no fault there. I disconnected the cables, took it out to satisfy my curiosity and put it back in. We thought about not putting it back in, and just buying a case to use it as an external. But there were a series of questions that led us deciding to put it back in. Who goes to the market to check for the case? Will it be available here? Is it worth it?
Next, I screwed the hinge knots back in. The right hinge is just above the cooler fan and the left hinge…well, I don’t know what it’s above so you tell me. The laptop is a very old one, and one that has never been opened before. So I believe it was a first time for both of us lol.
These 3 knots in line at the end really stressed me out when I was opening it up. We didn’t have screws to work with, so we used a knife. Now these knots were so small the knife wouldn’t fit. In the end, the part where the screw fixed became circular and frictionless, so couldn’t be screwed out because we forced the knife in, and turned in attempts to screw several times.
Side view of the laptop’s cover
View from above
Next was placing the cd disk drive(or whatever it’s called) in. I don’t remember how I took it out, so I invented my own back-in strategy. For this part, I put the disk drive on the back of the laptop’s cover and later just put the top of the laptop on it.
This is the disk drive. Notice the two USB-looking parts at the edge, they fit perfectly into a socket on the laptop’s cover which you’ll notice if you watched the side view of the laptop back’s picture carefully. Once you fit it in, this is what it looks like.
Notice that cable I’m holding I’ll be doing something with it. That is basically what connects the disk drive to the mother board.
The cable passes through an opening of the keyboards layout to connect to a socket on the motherboard. This side is no longer the back of the laptop, but the front. I’m sure you can see the mousepad and the dell sticker. If the disk cable plugs into the socket, this is what it looks like.
Now one more cable connection on the top side and we’re done with cables! This cable to be connected now is for the keyboard itself. After plugging the cable to it’s socket, you need to press these small locks to lock the keyboard in place so it doesn’t fall off if you raise the laptop.
If this didn’t bore you to death and you’re still here, good job, we’re almost done:) I flipped to the back again to tighten the screws there. This part was the easiest. The knots here weren’t difficult to handle even with the knife.
And now were done, this is what our laptop with all pieces together looks like. I have to say though, I probably put a lot of things where they weren’t supposed to be, but as long as they fit, I was fine with it lol.
I power the laptop up and I still see the same old not encouraging message. It was all a waste! We’ll probably just give it to a computer science student tomorrow to fix for us. I’m sure they’d be more than willing to help once they know the bounty that awaits inside the laptop haha.
I am 
Click the image above to sign up on presearch, a decentralized search engine where you earn PRE tokens for searching content on the internet, just like you already do with google.
