DJI Osmo waterproof case for pocket
It's not in the picture, but I bought all the accessories for pocket because of the accessory kit.
It's been a long time since I've been out of the pocket case because I can not get my pockets out nowadays.
It is a waterproof case first.
There are three things that look like case body and gum, but it's like a dampener (silica gel).
It is said that the inside of the case should be put together when using the case so that the inside of the device is not damped by moisture.
I do not know whether it was more careful than the existing waterproof case or it was more cumbersome.
It is not price right now, but I put the body only in the case and tested it.
Unlike conventional action cams, Osmo Pocket is set to waterproof case mode, and after power off
After mounting the case, you need to turn it on again.
In case of waterproof case, change of gimbal mode or self-mode is not executed.
Gimbal movement is like FPV mode.
Perhaps a round cover will block the perimeter and only look at the field of vision
It seems to move the gimbal quickly.
The front of the case-mounted Osmo pocket is like this.
It was replaced with a black cover that was not visible when it was released at the time of the original OSMO pocket.
When shooting in water, the quality of the content will deteriorate due to the reflection of the frame except for the front.
I am afraid that I am concerned.
It is not a deep water shot, but a transparent cover
I feel sorry for what it would have been like if it had been enclosed.
It is the state of removing the cover part of the camera.
There is a separate clip inside the case to hold the camera and the clip when attaching the pocket to the case.
It is not difficult to mount, but be careful when removing the case.
When I pulled out the pocket, the internal tightness was better than I expected and it did not come off easily.
It's easy to get to the gimbal side, but it can be very lethal to your device.
You must push your fingers as far as possible into the bottom of the gimbal handle.
It is an insert type mounting so you have to be very careful when removing it ...
It is an item that is used in many ways such as utilization and inconvenience.
(Maybe the review will be the last disposal angle ㅠ!
Rainy days should just go to action cam + waterproof case ㅠ)
But the extension load is a very satisfying item.
Once the first appearance looks just as bad as a celluloid bar.
But Osmo Pocket is almost an Osmo Pocket 2 or more item that makes more than a barrel.
The button part has been upgraded greatly compared to the existing Osumo pocket.
If you have used the existing Osmo Mobile or Osmo 1 gimbal, gimbal camera, etc., there is a familiar jog shuttle.
This allows you to control the movement of the camera much more freely.
Although it is not visible in the above picture, the right side of the control part has a mode to move the camera freely with the jog shuttle
There is a switch that allows you to adjust between two modes that can only move up and down and up and down.
The C1 button toggles the gimbal mode freely.
The C2 button is a function of the trigger (trigger) button on the existing OSMO model and is a gimbal lock function
The Fn button is the same as the right button on the Osmo pocket (power, center gimbal alignment, etc.)
I do not know if everyone knows the switch button and shoot button.
In addition to the purpose of wide field of view, it is possible to shoot various methods by upgrading the control part
The utilization of the expansion rod seems to be very high.
Osumo smartphone equipped with a wireless base was attached to the extension rod and connected.
The fixed base of the smartphone can be raised so that it can be monitored easily by shooting angle depending on the angle of the rod.
It was a simple test, but the temperature difference between the two was too big.
The bottom line is the extension load!
I hope that the pocket users will enjoy the feeling of upgrading OSMO Pocket 1 to OSMO Pocket 2 with the expansion rod.
